What problems should be paid attention to when installing multihead weigher

2022/09/08

Author: Smartweigh–Multihead Weighter

After the enterprise purchases the multihead weigher, it is necessary to install the multihead weigher. What problems should be paid attention to when installing the multihead weigher? Let's take a look at the issues that need to be paid attention to during the installation of multihead weigher. Multihead weigher installation issues needing attention 1: Before training and installation, the multihead weigher supplier should provide operator training on the production site. After the operator is fully trained and qualified, he can deeply understand the specific multihead weigher system to cooperate with the installation. And ensure fast, efficient and safe daily operation and maintenance, so that the multihead weigher obtains a long service life. Problems that need to be paid attention to in the installation of multihead weigher 2: Points for attention in installation Since the multihead weigher is supplied as an independent single device, its installation requirements are relatively simple, you can refer to the following points for installation: 1) When the multihead weigher is transported by a forklift, make sure the fork Do not damage the load cell.

2) As an integral part of the packaging production line, the multihead weigher is usually integrated with other equipment on the same production line, such as packaging machines, metal detectors, X-ray inspection devices, visual inspection devices, inkjet printers, labeling machines, rejection device etc. Therefore, it is necessary to consider placing them in a certain logical order. 3) The installation location of the multihead weigher should be selected in an area that will not be directly or indirectly subjected to vibration and mechanical shock.

4) The installation location of the multihead weigher should be selected in an area with the lowest possible air flow speed, and a wind shield can be installed if necessary. 5) The multihead weigher must be installed on a sturdy platform on a level ground, and the multihead weigher must be firmly bolted to the ground to ensure that it does not move, twist or bend during use. 6) The front and rear connection points of the multihead weigher device are the input segment and the output segment, which are close to each other but leave a gap. The multihead weigher cannot have any contact with these points and should be completely independent.

7) The multihead weigher requires space on the belt or chain drive side to clean and replace the conveyor. Installation, commissioning and inspection are also required to allow space on the opposite side for calibration and cleaning. 8) The multihead weigher should not be installed near sources of strong electromagnetic interference.

9) If the multihead weigher is installed in an explosion-hazardous environment, it should be ensured that all components in the multihead weigher structure meet the requirements for special protection devices classified in industrial explosion-proof hazardous areas. 10) All metal protective plates and components in contact with the multihead weigher should be grounded reliably, and the power plug should be properly grounded to ensure the personal safety of operators. 11) When the multihead weigher is moved and reused, the zero-setting operation must be performed first, and then the product check-weighing can be performed.

Problems that need to be paid attention to in the installation of multihead weigher 3: Inspection after installation After installation, the multihead weigher should be started and checked as follows: 1) The conveyor belt is running smoothly; 2) The conveyor belt is centered; 3) The conveyor belt of the input section and the output section No contact; 4) The speed of the conveyor belt matches the displayed value; 5) The rejection device operates correctly; 6) The photoelectric switch operates correctly; 7) There is no vibration on the load cell. The above sharing is about the issues that need to be paid attention to in the installation of multihead weigher. I hope it will be helpful to you.

Author: Smartweigh–Multihead Weighter Manufacturers

Author: Smartweigh–Linear Weighter

Author: Smartweigh–Linear Weigher Packing Machine

Author: Smartweigh–Multihead Weighter Packing Machine

Author: Smartweigh–Tray Denester

Author: Smartweigh–Clamshell Packing Machine

Author: Smartweigh–Combination Weighter

Author: Smartweigh–Doypack Packing Machine

Author: Smartweigh–Premade Bag Packing Machine

Author: Smartweigh–Rotary Packing Machine

Author: Smartweigh–Vertical Packaging Machine

Author: Smartweigh–VFFS Packing Machine

CONTACT US
Just tell us your requirements, we can do more than you can imagine.
Send your inquiry
Chat
Now

Send your inquiry

Choose a different language
English
العربية
Deutsch
Español
français
italiano
日本語
한국어
Português
русский
简体中文
繁體中文
Afrikaans
አማርኛ
Azərbaycan
Беларуская
български
বাংলা
Bosanski
Català
Sugbuanon
Corsu
čeština
Cymraeg
dansk
Ελληνικά
Esperanto
Eesti
Euskara
فارسی
Suomi
Frysk
Gaeilgenah
Gàidhlig
Galego
ગુજરાતી
Hausa
Ōlelo Hawaiʻi
हिन्दी
Hmong
Hrvatski
Kreyòl ayisyen
Magyar
հայերեն
bahasa Indonesia
Igbo
Íslenska
עִברִית
Basa Jawa
ქართველი
Қазақ Тілі
ខ្មែរ
ಕನ್ನಡ
Kurdî (Kurmancî)
Кыргызча
Latin
Lëtzebuergesch
ລາວ
lietuvių
latviešu valoda‎
Malagasy
Maori
Македонски
മലയാളം
Монгол
मराठी
Bahasa Melayu
Maltese
ဗမာ
नेपाली
Nederlands
norsk
Chicheŵa
ਪੰਜਾਬੀ
Polski
پښتو
Română
سنڌي
සිංහල
Slovenčina
Slovenščina
Faasamoa
Shona
Af Soomaali
Shqip
Српски
Sesotho
Sundanese
svenska
Kiswahili
தமிழ்
తెలుగు
Точики
ภาษาไทย
Pilipino
Türkçe
Українська
اردو
O'zbek
Tiếng Việt
Xhosa
יידיש
èdè Yorùbá
Zulu
Current language:English