loading

Vertical packaging machine of common failures and solutions ( All)

2020/04/15
Common faults a: 1, the cutter rotating. Failure to failure reason: spin. Damaged or treatment method of the boundary question: in a spin encoding input, check the wiring, 2. , cutter motor fault can cause: motor damage or frequency converter fault or mechanical jammed with common one: 1, the cutting knife spin. Failure to failure reason: spin. Damaged or treatment method of the boundary question: in a spin encoding input, check the wiring, 2. , cutter motor fault can cause: motor damage or frequency converter fault or mechanical jammed the solution: to view the corresponding fault point 3, paper feed motor fault can cause: motor damage or frequency converter fault or mechanical jammed the solution: to view the corresponding fault point 4, magic eye can fault reason: to check the color code sensor or the quality of the packaging film the solution: replace the corresponding equipment 5, short of paper failure to failure reason: no packaging film the solution: replace the new packaging film 6, system failure can failure reason: control device self-checking troubleshooting way. To contact the supplier if the fault has been swept away, just press the ESC key system will run active reply said. Common failure 2: failure surface: 1, block bearing against color code 2, cutting knife cutting 3, pincer-like device present coke wrinkle marks on commodities 4, sealing not firm or leak sealing 5, thermometer can't control temperature reason analysis: 1, color standard Shadowed did not open, film color standard colour is too light, thin film drive slippage. 2, push rod and the cutter is not synchronous, cutter holder packing speed is too high or too low, too fast. 3, the temperature is too high, too slow, coated outer heat resistance is poor. 4, temperature is too low, too fast, coated inner poor heat sealing. 5, heating element damage, solid state relay, thermocouple damage, damage to the temperature control table, burn out. Cleaning method: 1, the scrutiny in man-machine interface method of interface, the Shadowed method to switch to the 'Shadowed cut'; Visit random magic eye specifications, adjust the photoelectric sensor sensitivity; Regulate rubber roller pressure or brake slack. 2, visit manual adjustment refers to the bearing; Regulate side sealing part is concave and convex, make the sealing knife meshing center is at the centre of the commodity highly orientation; Packing speed down. 3, lowering temperature; Adjustable speed; Replace the film material. 4, replace the heating element, in solid state relay, galvanic replacement and replacement temperature control table.
CONTACT US
Just tell us your requirements, we can do more than you can imagine.
Send your inquiry
Chat
Now

Send your inquiry

Choose a different language
English
العربية
Deutsch
Español
français
italiano
日本語
한국어
Português
русский
简体中文
繁體中文
Afrikaans
አማርኛ
Azərbaycan
Беларуская
български
বাংলা
Bosanski
Català
Sugbuanon
Corsu
čeština
Cymraeg
dansk
Ελληνικά
Esperanto
Eesti
Euskara
فارسی
Suomi
Frysk
Gaeilgenah
Gàidhlig
Galego
ગુજરાતી
Hausa
Ōlelo Hawaiʻi
हिन्दी
Hmong
Hrvatski
Kreyòl ayisyen
Magyar
հայերեն
bahasa Indonesia
Igbo
Íslenska
עִברִית
Basa Jawa
ქართველი
Қазақ Тілі
ខ្មែរ
ಕನ್ನಡ
Kurdî (Kurmancî)
Кыргызча
Latin
Lëtzebuergesch
ລາວ
lietuvių
latviešu valoda‎
Malagasy
Maori
Македонски
മലയാളം
Монгол
मराठी
Bahasa Melayu
Maltese
ဗမာ
नेपाली
Nederlands
norsk
Chicheŵa
ਪੰਜਾਬੀ
Polski
پښتو
Română
سنڌي
සිංහල
Slovenčina
Slovenščina
Faasamoa
Shona
Af Soomaali
Shqip
Српски
Sesotho
Sundanese
svenska
Kiswahili
தமிழ்
తెలుగు
Точики
ภาษาไทย
Pilipino
Türkçe
Українська
اردو
O'zbek
Tiếng Việt
Xhosa
יידיש
èdè Yorùbá
Zulu
Current language:English