General criteria used by multihead weighers

2022/10/03

Author: Smartweigh–Multihead Weighter

In the weighing equipment, which kind of multihead weigher is used, it is necessary to consider all aspects. The following describes the multihead weigher's structural form, measurement range, and selection of accuracy levels that generally need to be considered. 1. The selection of structure and method of multihead weigher depends on the environmental standards of electronic structure and application.

If you want to make low-design electronics, you should generally use cantilever beam type and wheel-spoke type sensors. If the aspect ratio of the design is not strictly controlled, you can choose a column type sensor. In addition, if the natural environment of electronic applications is very humid and cold, and there is a lot of smoke and dust, you should choose a good sealing method; if there is a risk of explosion, you should use a safety culture sensor; if you are on an elevated road In heavy equipment, safety and overvoltage protection should be considered; if it is used in a high-temperature natural environment, a multihead weigher with a cooling water jacket should be used; if it is used in severe cold areas, it should be considered to select a multihead weigher with heating device sensor. In the selection of the method, one factor to be considered is whether the maintenance is convenient and the cost, that is, once the weighing equipment fails, whether the maintenance components can be obtained successfully and quickly.

If there is no guarantee, it means that the selection of the method is not suitable. 2. Selection of measurement range The closer the weighing value of the weighing device is to the short-circuit capacity of the switch, the higher the weighing accuracy. , wheel weight, etc., so there are very big differences in the standard of the limit of the sensor used by different weighing system software. As a general standard, there are: *Single sensor static data Weighing equipment: fixed load (weighing platform, utensils, etc.) + variable load (load to be weighed)≤The rated load of the sensor used X70%*Multi-sensor static data Weighing equipment: fixed load (weighing platform, utensils, etc.) + variable load (load to be weighed)≤Using the rated load of the sensor X the number of sensors used X 70%, the index of 70% is added considering factors such as vibration, impact, and wheel weight.

It must be pointed out that: first of all, the short-circuit capacity of the sensor should be as close as possible to the value in the manufacturer's standard product series, otherwise, the use of non-standard products is not only expensive, but also cannot be replaced after damage. Secondly, in the same weighing equipment, it is not allowed to use sensors with different short-circuit capacities, otherwise, the system software cannot work normally. Secondly, to put it bluntly, the changing load (the load that needs to be weighed) refers to the real load applied to the sensor. If the force value is transmitted from the weighing platform to the sensor, there is a multiplication and attenuation coefficient organization (such as a rod). lever system software), its hazards should be considered.

3. The selection of accuracy The selection of the accuracy level of the multihead weigher should be able to consider the regulations on the accuracy level of the weighing equipment, if this regulation can be considered. That is, if the sensor with the 2500 measurement range can meet the requirements, do not use the 3000 measurement range. If several same methods are used in a weighing equipment, when the inductors with the same short-circuit capacity are connected in series, the reason for the comprehensive deviation is Δ, then: Δ=Δ/n1/2(2—12) Among them: Δ: the reason for the deviation of the comprehensiveness of the individual sensors; n: the number of sensors.

In addition, electronic weighing equipment is generally composed of three major components, which are weight sensors, weighing displays and mechanical equipment parts. When the error value of the system software is 1, the reason (Δ) of the comprehensive deviation of the multihead weigher, which is one of the key components of non-automatic electronics, is generally only a proportion of 0.7. Based on this and equation (2--12), it is not too difficult to choose the required sensor accuracy.

4. How should some special requirements be achieved? In some weighing equipment, there may be some unique regulations. For example, in the rail scale, the elastic deformation of the multihead weigher is expected to be smaller, so that the weighing platform can be under the condition of weighing. Smaller displacements reduce shock and vibration when large trucks drive in and out of the weighing platform. In addition, when composing dynamic weighing equipment, it is inevitable to take into account the natural frequency of the commonly used multihead weigher, whether it is possible to consider the provisions for accurate dynamic measurement. This main parameter is not listed in the general product introduction.

Therefore, if you want to master this performance parameter, you should consult the manufacturer to prevent errors.

Author: Smartweigh–Multihead Weighter Manufacturers

Author: Smartweigh–Linear Weighter

Author: Smartweigh–Linear Weigher Packing Machine

Author: Smartweigh–Multihead Weighter Packing Machine

Author: Smartweigh–Tray Denester

Author: Smartweigh–Clamshell Packing Machine

Author: Smartweigh–Combination Weighter

Author: Smartweigh–Doypack Packing Machine

Author: Smartweigh–Premade Bag Packing Machine

Author: Smartweigh–Rotary Packing Machine

Author: Smartweigh–Vertical Packaging Machine

Author: Smartweigh–VFFS Packing Machine

CONTACT US
Just tell us your requirements, we can do more than you can imagine.
Send your inquiry
Chat
Now

Send your inquiry

Choose a different language
English
العربية
Deutsch
Español
français
italiano
日本語
한국어
Português
русский
简体中文
繁體中文
Afrikaans
አማርኛ
Azərbaycan
Беларуская
български
বাংলা
Bosanski
Català
Sugbuanon
Corsu
čeština
Cymraeg
dansk
Ελληνικά
Esperanto
Eesti
Euskara
فارسی
Suomi
Frysk
Gaeilgenah
Gàidhlig
Galego
ગુજરાતી
Hausa
Ōlelo Hawaiʻi
हिन्दी
Hmong
Hrvatski
Kreyòl ayisyen
Magyar
հայերեն
bahasa Indonesia
Igbo
Íslenska
עִברִית
Basa Jawa
ქართველი
Қазақ Тілі
ខ្មែរ
ಕನ್ನಡ
Kurdî (Kurmancî)
Кыргызча
Latin
Lëtzebuergesch
ລາວ
lietuvių
latviešu valoda‎
Malagasy
Maori
Македонски
മലയാളം
Монгол
मराठी
Bahasa Melayu
Maltese
ဗမာ
नेपाली
Nederlands
norsk
Chicheŵa
ਪੰਜਾਬੀ
Polski
پښتو
Română
سنڌي
සිංහල
Slovenčina
Slovenščina
Faasamoa
Shona
Af Soomaali
Shqip
Српски
Sesotho
Sundanese
svenska
Kiswahili
தமிழ்
తెలుగు
Точики
ภาษาไทย
Pilipino
Türkçe
Українська
اردو
O'zbek
Tiếng Việt
Xhosa
יידיש
èdè Yorùbá
Zulu
Current language:English